iTrip H-100 tripmeter

The backlit graphic display ensures perfect readability of the measured parameters. The main measurement parameters have 14 mm high digits and a bold font. The auxiliary parameters and time, as secondary parameters, are displayed in a standard font with a smaller height. The display is protected with a film that protects against moisture and dirt.

Convenient backlight adjustment allows you to adjust the brightness of the tripmeter screen to external conditions.

• one entry works with one road sensor
• one input works with one distance sensor, a backup sensor is connected to the other input in order to make a change in case of an emergency
• two inputs with two sensors work simultaneously. The tripmeter performs simultaneous measurements from two sensors mounted on the right and left side of the vehicle, which increases the precision of the measurement

All iTrip tripmeters have a special warning system for a total failure of the speed sensor or for emerging problems with the stability of the speed signal.

Each sensor is matched by a two-color LED on the front panel. It signals the work of sensors and their activity. Visible signaling that there is no speed signal while driving the vehicle indicates problems with its operation or errors in matching the sensor type to the tripmeter.

Sensor control is carried out continuously.

Measurements of the short TRIP route path and the long ODO route can be presented in one of three resolutions, selected by the competitor using the tripmeter. The resolution of the distance indication also affects the value of the long-distance ODO correction:

The countdown mode allows you to measure the distance in the opposite direction, ie the countdown of the road back. In practice, this function can be used, for example, in a situation of getting lost. When returning to the place of getting lost, turn on the countdown function and turn it off when you return to the correct route. As a result, the distance measured by the tripmeter will not include the distance traveled on the wrong route.

You can enable the function with a switch connected to one of the harness wires marked as: Driving backwards.

Tripmeter can work with two independent resetters, which allow you to control some functions without the need to operate buttons on the tripmeter. In many situations, the external resetter is faster and ensures no errors caused by accidentally pressing the wrong buttons.

Tripmeter can be equipped with a waypoint routing function based on the given course and distance to the destination. To display the route to the destination, it uses the mobile arrow displayed on its display and the auxiliary numerical values of the distance to the destination and the course to the destination.

The tripmeter can display the route to the destination on a connected Garmin device which then works as an external tripmeter display.

Data for routing waypoints can be entered before the start of the rally/section.

You can enter your data using the tripmeter keyboard as well as prepare files on your computer or tablet and copy them to the tripmeter using a memory stick.

Routing the waypoint takes place in a fraction of a second. There is no need to stop or decrease the speed during the routing.

The tripmeter can be attached to any type of vehicle. It has built-in up to 8 fixing points with an M4 thread, which guarantee that during the trip the tripmeter will be fixed to the vehicle.

The tripmeter has a useful function of adjusting the long ODO path. If the distance measured does not entirely match the distance provided by the organizer, you can use the arrow keys to make a quick correction. The correction value following each key press is related to the display resolution and is: 1, 10 or 100 m.

When you hold down the button, the correction will be repeated.

You can also make a full correction of the long ODO road by entering its value into the tripmeter.

When you use the waypoint routing function, you can use the Garmin device as an additional display of the tripmeter. The Garmin display along with a displayed map and a route to the waypoint will make the route more transparent than ever before.

Working with the driver's external display.

• wbudowany GPS ( opcja GPS )
• dwa niezależne liczniki drogi z możliwością kasowaniu
• maksymalny zakres drogi - do 999,9 km
• możliwość korekty drogi długiej - szybka korekta o zadaną wartość lub wpisanie dowolnej wartości
• dwa niezależne wejścia czujników pracujące w 3 konfiguracjach
• system kontroli stanu czujników drogi
• w przypadku awarii czujników możliwość przełączenia na naliczanie z GPS podczas pomiarów ( opcja GPS )
• podświetlane przyciski
• kontrastowy wyświetlacz LCD o wysokości cyfry 14mm
• elektroniczna ochrona pamięci nastaw i pomiarów
• czytelna sygnalizacja stanu i zasięgu GPS ( opcja GPS )
• wskazanie prędkości
• wskazanie kursu ( opcja GPS )
• wskazanie napięcia w sieci pojazdu
• wskazanie czasu
• synchronizacja czasu z GPS ( opcja GPS )
• ręczna lub automatyczna ( opcja GPS ) kalibracja
• pamięć do 10 współczynnik kalibracyjnych
• możliwość zmiany współczynnika podczas pomiarów
• możlwość korekty współczynnika podczas pomiarów
• trasowanie azymutów w urządzeniach garmin ( opcja GPS + Azymut )
• nawigowanie do punktu końcowego za pomocą strzałki na ekranie ( opcja GPS + Azymut )

• wbudowany ultraszybki moduł GPS
• trasowanie azymutów. Funkcja pozwala na trasowanie waypointów na podstawie podanego azymutu oraz odległości do celu.

• Napięcie zasilania : 8 ÷ 30V
• Pobór prądu : max. 200mA
• Wysokość : 91 mm
• Szerokość : 135 mm
• Głebokość : 32 mm
• Waga : 690 g

• instrukcja do przeglądania, drukowania, pobierania
• schemat podłączenia ( plik .pdf )